Divider design
In the last lesson you could give a resistor any value you liked. A real parts drawer isn't so generous. Resistors are made in a fixed set of preferred values, and the usual set has twelve to each decade:
| 1.0 | 1.2 | 1.5 | 1.8 | 2.2 | 2.7 |
| 3.3 | 3.9 | 4.7 | 5.6 | 6.8 | 8.2 |
and then the same again ten times bigger: 10, 12, 15… So there's a 4.7 kΩ and a 5.6 kΩ, but no 5 kΩ. Each value is about 20% bigger than the last, so you're never more than about 10% from the value you wanted.
A design also has a budget. A divider draws current from the supply all the time it is connected, doing nothing but setting a voltage. On a battery, that current is the price of the divider.
You want exactly 6 kΩ. Which preferred value is nearest?
- 5.6 kΩ
- 6.0 kΩ
- 6.8 kΩ
Step 1: the total, from the current
The two resistors are in series across the supply, so the current the pair draws is
A current limit therefore sets the smallest total resistance you may use:
A divider across a 9 V supply may draw at most 0.5 mA. What is the smallest total resistance it can have?
Answer in Ω.
Step 2: the split, from the voltages
The same current flows through both resistors, so their voltages are in the same ratio as their resistances. The bottom resistor has across it, and the top one has what's left:
Worked example. 3.3 V from a 9 V supply:
So the top resistor must be 1.73 times the bottom one: with a 10 kΩ bottom resistor, 17.3 kΩ.
Now you. For 2 V from a 12 V supply, with = 10 kΩ, what must be?
Answer in Ω.
Step 3: preferred values, then check
Back to the worked example: 3.3 V from 9 V, drawing at most 1 mA.
- Total at least 9 V ÷ 1 mA = 9 kΩ.
- Ratio = 1.73.
- Try a bottom resistor and see what the top one would need to be:
| R2 | R1 wanted | Nearest value | Vout | Error |
|---|---|---|---|---|
| 3.3 kΩ | 5.7 kΩ | 5.6 kΩ | 3.34 V | +1.1% |
| 3.9 kΩ | 6.7 kΩ | 6.8 kΩ | 3.28 V | −0.6% |
| 4.7 kΩ | 8.1 kΩ | 8.2 kΩ | 3.28 V | −0.6% |
| 5.6 kΩ | 9.7 kΩ | 10 kΩ | 3.23 V | −2.1% |
- Check both limits with the real values. One of these four rows fails the current limit. Which?
- 3.3 kΩ with 5.6 kΩ
- 3.9 kΩ with 6.8 kΩ
- 4.7 kΩ with 8.2 kΩ
- 5.6 kΩ with 10 kΩ
Your turn. Design and build a divider across the 9 V battery that gives 2.5 V, to within 5%, and draws no more than 0.5 mA.
The drawer's resistors come only in preferred values, from 1 kΩ to 100 kΩ.
A tighter one. This output is a reference that something else will be compared against, so it has to be closer.
On this fresh board, build a divider across the 9 V battery that gives 3.3 V to within 2%, drawing no more than 1 mA.
Bigger resistors waste less current. So why not always build dividers from 1 MΩ and 10 MΩ resistors, and waste almost none?
- Whatever is connected to the output draws a little current, and a divider with very big resistors can't supply it without its voltage changing
- Big resistors get hotter than small ones
- The formula stops working above 100 kΩ
Designing a divider:
- the current budget sets the smallest total: ;
- the voltages set the ratio: ;
- round to preferred values, trying a few bottom resistors to find a pair that lands close;
- check the output and the current again with the values you'll really use.
On a real bench resistors also have a tolerance. Two 5% resistors can put a divider's output out by several percent on their own, so a tight reference uses 1% parts, which come in a finer set of 96 values to the decade.